WatchGuard Technologies FireboxTM System 4.6 Uživatelský manuál Strana 31
- Strana / 170
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
User Guide 21
CHAPTER 4 Firebox Basics
This chapter describes the following tasks, which require direct interaction between
the Management Station and the Firebox:
•Set up a Firebox
• Open and save a configuration file to a local hard disk or the Firebox
• Reset Firebox passphrases
• Set the Firebox time zone
• Reinitialize a misconfigured Firebox
• Manage the flash memory of the Firebox
What is a Firebox?
Fireboxes are specially designed and optimized machines. They are small, efficient,
and reliable.
There are no user-serviceable parts within the Firebox. If a user
opens a Firebox case, it voids the limited hardware warranty.
- WatchGuard 1
- System 1
- User Guide 1
- Disclaimer 2
- WatchGuard Technologies, Inc 3
- Firebox System Software 3
- End-User License Agreement 3
- Declaration of Conformity 5
- FCC Certification 6
- CE Notice 6
- Table of Contents 7
- User Guide ix 9
- Introduction 11
- WatchGuard Firebox 12
- WatchGuard Control Center 12
- WatchGuard security suite 12
- Minimum requirements 13
- Hardware requirements 14
- Services 15
- LiveSecurity Service 17
- LiveSecurity broadcasts 18
- User Guide 9 19
- Technical Support 21
- Getting telephone support 22
- Training 23
- WatchGuard users group 24
- Online Help 24
- Searching for topics 25
- Context-sensitive Help 26
- WatchGuard Options 27
- Obtaining WatchGuard options 28
- Configuring a Security Policy 29
- Firebox Basics 31
- Internet 32
- Opening a configuration file 33
- Saving a configuration file 33
- Resetting Firebox passphrases 34
- Install Guide 35
- Booting from the system area 36
- Using the WatchGuard Control 37
- QuickGuide 38
- Front panel 38
- Firebox and VPN tunnel status 38
- Remote VPN tunnels 39
- Red exclamation point 39
- Traffic Monitor 40
- Changing the polling rate 40
- Policy Manager 41
- LogViewer 42
- Historical Reports 43
- LiveSecurity Event Processor 43
- Configuring a Network 45
- Install Guide 46
- Setting up a routed network 47
- Adding a secondary network 48
- Defining a network route 48
- Defining a host route 49
- Setting the default gateway 49
- Adding a new subnet 50
- Modifying an existing subnet 51
- Removing a Subnet 51
- Blocking Sites and Ports 53
- Blocking a site permanently 54
- Blocking a port permanently 55
- Configuring Services 57
- Creating a new service 58
- Working with wg_ icons 60
- Modifying a service 61
- Deleting a service 61
- Setting up proxy services 62
- Add masquerading options 64
- User Guide 55 65
- User Guide 57 67
- Service precedence 67
- Controlling Web Traffic 69
- Logging and WebBlocker 70
- Activating WebBlocker 70
- Setting Up Network Address 73
- Translation 73
- Using simple dynamic NAT 74
- Using service-based NAT 75
- Adding external IP addresses 76
- User Guide 67 77
- Setting Up Logging and 79
- Notification 79
- Adding an Event Processor 81
- Enabling Syslog logging 81
- Removing an Event Processor 82
- Reordering Event Processors 82
- User Guide 73 83
- Viewing the Event Processor 84
- User Guide 75 85
- Scheduling log reports 86
- Controlling notification 86
- User Guide 77 87
- Connect with Out-of-Band 89
- Management 89
- Install the modem 90
- OOB time-out disconnects 91
- VPN Manager Guide 83 93
- Creating Aliases and 95
- Implementing Authentication 95
- Adding a host alias 96
- Modifying a host alias 96
- Removing a host alias 96
- What is user authentication? 97
- VPN Manager Guide 89 99
- VPN Manager Guide 91 101
- Monitoring Firebox Activity 103
- Reference Guide 104
- User Guide 95 105
- Firebox Monitors 105
- User Guide 97 107
- HostWatch 108
- Connecting to a Firebox 109
- Replaying a log file 109
- Viewing specific hosts 110
- Viewing specific ports 110
- Viewing authenticated users 110
- Modifying view properties 111
- Viewing files with LogViewer 113
- By keyphrase 114
- By field 114
- Copying log data 114
- Exporting log data 114
- Displaying and hiding fields 115
- Working with log files 116
- Firebox IP Time Stamp 117
- Firebox IP 117
- Activity 119
- Specifying report sections 120
- Specifying a report time span 121
- Consolidating report sections 121
- Setting report properties 121
- Exporting reports 122
- Filter Name 123
- Editing a filter 124
- Deleting a filter 124
- Applying a filter 124
- Scheduling a report 124
- Manually running a report 125
- Consolidated Sections 127
- Virtual Private 129
- Networking 129
- Private Networking 131
- How does DVCP work? 132
- Basic and Enhanced DVCP 132
- Editing a tunnel to a device 133
- Branch office VPN with IPSec 134
- Configuring a gateway 135
- Removing a gateway 136
- User Guide 127 137
- Creating an IPSec policy 138
- Changing IPSec policy order 139
- Configuring WatchGuard VPN 140
- User Guide 131 141
- Configuring the Firebox for 143
- Remote User VPN 143
- Adding remote access users 144
- By individual service 145
- Using the Any service 145
- Activating Remote User PPTP 146
- User Guide 137 147
- Entering license keys 148
- User Guide 139 149
- Configuring debugging options 150
- Preparing a Host for Remote 151
- User VPN 151
- Remote host operating system 152
- User Guide 143 153
- User Guide 145 155
- Using Remote User PPTP 156
- User Guide 151 161
- User Guide 153 163
- User Guide 155 165
- User Guide 157 167
- User Guide 159 169
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.137 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce